Friday, November 15, 2013

It could happen again [updated]

As we near another anniversary of the Halifax Explosion of  December 6, 1917, it is tempting to think about whether such an event could occur again.

In the infamous explosion two ships, Mont Blanc and IMO, collided in the Narrows (off pier 6). A fire ensued, igniting the cargoes of explosives on both ships. The resulting blast killed more than a thousand, maimed legions more, leveled the north end of town and sank or badly damaged a score of ships.

Nowadays a similar scenario is perhaps unthinkable, since two ships are unlikely to meet each other in the Narrows. We have radar, VHF Radio, Vessel Traffic Management, satellite navigation and lots of safety factors built in to shipping. But there is a scary "what if" which should be considered by the various authorities responsible for the the harbour. In fact it requires little imagination to see how that "what if"  might unfold because some of it has already happened and we were saved from potential disaster.

Late in the evening of November 4, 2013 or in the early morning hours of November 5, 2013 the post-Panamax container ship OOCL Oakland sailed from Fairview Cove for sea. As it transitted the Narrows it lost power. This is where the "what if" kicks in.

OOCL Oakland lost power in the Narrows.

1. What if the ship, without power, had drifted into either of the harbour bridges?
2. What if the ship, without power, had drifted up on the shore or into any of the piers or harbour installations, blocking the Narrows for shipping?
3. What if it had dangerous cargo aboard which caught fire or spilled? 

Fortunately none of these "what ifs" took place-for one very good reason. The ship was using a stern tethered tug to act as rudder and brake. The tug was able to keep the ship on its course as it gradually lost speed and controlled the ship until power was regained. Tethered escort tugs are used widely around the world, and have been proven to be able to exert tremendous forces to redirect or stop ships. The 4,000 to 5,000 bhp tugs in Halifax are capable of providing this braking/steering, but only if they are connected to the ship by stern line. 
By slewing to one side or the other and using its power, the tug can slow or turn a the ship quickly.


Atlantic Oak, at 5,000 bhp is the most powerful tug in Halifax, and is the one usually designated for tethered escort. Here it is exerting some sideways thrust to the container ship Yantian Express to turn it as it exits the Narrows into Bedford Basin.

As food for thought all ships are NOT required to have tethered escort tugs while steaming through the Narrows, In fact some ships larger than OOCL Oakland do not always use tethered escorts, although they might have tugs accompanying them, the tugs are not made up with lines, so in case of emergency could push, but not pull.
The post-Panamax APL Cyprine enters the Narrows without a tethered escort. It is slightly larger than the OOCL Oakland. The tug is merely accompanying the ship, but with no line up it is limited as to what assistance it could provide if needed.
Update: The tug Atlantic Oak is indeed tethered by stern line to the ship in this photo- the line is slack and hard to see, but the tug could quickly control the ship if called to do so.
 
Large ships are built to sail the high seas efficiently. Once they get into port, and reduce speed they become less manageable. Due to a reduction in water flow past their rudders, they begin to lose the ability to steer effectively and lose steerageway completely at very low speeds.

Big ships take a long time to slow down, even from a speed of 8 knots, which may be their speed in the Narrows. If they cannot use the reverse thrust of their engines due to a loss of power, they then begin to lose speed slowly and lose steerage way at the same time, but can continue drifting (in some direction) for a mile or more.

Dropping an anchor from a moving ship is not an alternative. At most measurable speeds, the anchor will not hold on the bottom. Even if it just dragged on the bottom it would tend to slew the ship around as soon as it fetched up or snagged, creating a worse situation, particularly in a narrow channel.
 
Big ships at slow speeds need tugs for maneuvering.

Bow thrusters can be useful for course changes, but are most effective at low speeds to assist in docking. If a ship loses main propulsion power, it is likely to lose power to its thruster, since it is electrically driven from the ship's main power plant.


So let's go back to the what ifs:

1. What if the powerless ship (with no stern tethered tug) drifted into one of the bridges. Yes the bridge towers are protected by rock berms along the water line which could deflect a ship, but would be just as likely to hole it, slew it around and  still possibly damage the tower. Also large ships like OOCL Oakland have limited clearance under the centre of the bridge span. Would they have adequate clearance if they were off course by fifty of a hundred feet? No. Their signal mast or funnel could strike the bridge deck.
Rock berms around the bridge towers may protect the bridge from some types of strikes, but damage could still result to both bridge and ship.

2. What if the ship struck any of the piers, or the drydock at Halifax Shipyard (that has happened too) there would be damage to both ship and shore, and it could well be that the ship remained immobile for some time to come, blocking the channel. If the Narrows were to be blocked some Coast Guard ships and ships at Fairview Cove or National Gyspum could be trapped for a time.

An unescorted, laden chemical tanker passes under the A. Murray MacKay bridge. There may be dangerous goods in transit across the bridge too. Who knows what is in that container?

3. What if dangerous good were spilled or a fire started? Container ships carry dangerous goods - some lethally toxic or polluting, some explosive. The recent fire on Atlantic Cartier in Hamburg revealed that it was carrying a significant quantity of ammunition. As in the Mont Blanc, IMO case, sparks and leaks caused by impact, can start a fire very easily.

Atlantic Cartier (seen here in the Narrows with a tethered stern escort) caught fire while tied up in in Hamburg May 1, 2013. Longshoremen removed containers carrying ammunition before they could ignite. The fire was extinguished by shore based firefighters, and the fire was confined to the car deck. A burning ship which is not alongside a dock would be a different proposition.


Apparently those in authority do not want to contemplate these "what ifs". If they had, there would be regulations requiring large ships to use tethered escort tugs. Yes it costs money to hire an escort tug, but this is a public safety issue. Certainly for the ship's crews, but also for those ashore and along the waterfront.

On November 4, 2011, HMCS Preserver struck the Novadock at Halifax Shipyard, causing slight damage to both. Had it been a continer ship or tanker that struck, had there been a ship in the Novadock, it could have been much worse, and with more serious consequences.

For a port with the history of such a horrific disaster as the 1917 explosion, and with several recent events, it is a wonder that the use of stern escort tugs in the Narrows in not mandatory.

So can it happen again? Something similar certainly can.Do we need another disaster before authorities accept responsibility and make proper regulations?

Every large ship transiting the Narrows should have at least one tethered stern escort tug, and for the largest ships another tug made up alongside.It is interesting that they will need those two tugs to tie up once they reach Bedford Basin anyway.

.

Classics - time running out

There are a number of older ships still running in Canada despite all the predictions about their ultimate demise-but timwe is quickly running out for most of them.

The ferry Holiday Island sailed late this afternoon from Halifax Shipyard after a refit which included a sparkling new paint job. The ship is scheduled to be re-engined, which shows considerable faith by the Minister of Transport (her owner) that she has a good many years lefty in her. Built in 1971 she has certainly reached a respectable age.
1. Holiday Island at noon time today, ready to be floated out at 1600 hrs. Sharp eyes will detect HMCS Preserver in the background. Of similar vintage it is on the replacement list to be built by Seaspan as part of the NSPS.

Speaking of ferries the Trans St-Laurent reached her 50th anniversary this summer, without fanfare. Her owners Clarke Inc, a mere shadow of the former Clarke Shipping,  is down to just this one ship in Canadian waters (and one other, the container RoRo Shamrock in the Caribbean). With only about three years left on her charter to Société des Traversiers de Québec we should enjoy her while we can.
 2. Purpose built in 1963 for the Rivière-du-Loup to St-Siméon run, the ship is still going strong (it has never been anywhere near Halifax..)

Back to Halifax the wonderful CCGS Hudson sailed this afternoon on another scientific mission. Her days are numbered, because a replacement is part of the NSPS contract awarded to Seaspan in Vancouver. The new ship is still a few years away.
3. After a short evolution in Bedford Basin, CCGS Hudson enters the Narrows bound for sea at noon time today. Her replacement will not have the dramatic shear and graceful lines of this ship.

 Not so lucky is the laker Algoma Québecois. Built in 1963 by Canadian Vickers in Montreal as Québecois the ship sailed for original owners Eastern Lake Cariiers (Papachristidis) until 1972, then Upper Lakes Shipping until 2011 when she was acquired and renamed by Algoma. The ship was laid up at the end of the 2012 season and since June has been sitting in Toronto, where I was able to grab a quick shot of her last week.
4. Idle on the Toronto waterfront November 6 Québecois awaited her fate.

As early as tomorrow tugs will arrive to tow her to the scrappers in Port Colborne.

5. In 1995 she was still Québecois and was passing Quebec City when I took this photo. 

The ship has the sad distinction of being the second last operating cargo steamship in Canada. Her sister and fleet mate, which is not expected to sail beyond this season, Algoma Montréalais ex Montréalais is, for now the only (and will be last) steamer* in operation.  Were it not for the excellent construction of these ships and the care with which they were maintained - not to mention a great deal of time in fresh water- they would have been gone long ago. However their virtually indestructible steam turbine propulsion systems have kept them running when disels have supplanted steam almost everywhere in the world.

6. This may be last season for Algoma Montréalis and the for the last commercial steamship operation in Canada. 
Built to traditional laker design, with wheelhouse forward and maximum Seaway dimensions of the time, the sisters have outlasted several newer ships. To give another sense of their longevity, they were built with escrow credits, reserved from the sale of wartime built Victory ships. As a form of subsidy to Canadian shipyards, owners were allowed to sell the Victory ships to foreign owners, but the proceeds had to be used to finance construction of new ships in Canada. The canny shipowner owner, P.B.Papachrisitidis parlayed credits from a few war-built ships into a Great Lakes fleet, that was then sold to finance an international fleet, which is now Hellespont Shipping. He did not skimp however, these were among the finest lakers (and best looking) ever built.

[* One exception to the demise of steam, is the Toronto ferry Trillium. With steam reciprocating machinery, the 103 year old paddle wheeler is an incredible example of steam at its finest, however its operation could not be considered commercial in the same way as a a cargo ship.]
[Other exceptions include the steam tug Master in British Columbia, the excursion steamer Segwun in Muskoka, and a handful of non-operational preserved steamships such as CSS Acadia HMCS Sackville in Halifax and the passenger ships Keewatin and Norisle on the Great Lakes.]
[None of these are cargo ships, so we are truly seeing the end of an era..]

.

Wednesday, November 13, 2013

Bahri Hofuf - large cargo

The Saudi ship Bahri Hofuf had a large consignment of cargo to load today. There were numerous RoRo items including the usual quantity of a dozen or so military LAVs and a large wheel loader. The ship also worked containers using its own cranes.

Bahri Hofuf was accepted from builder Hyundai Mipo on May 1 of this year, and was the second of the new 50,000 gross ton ConRos to be delivered. The ship is deceptive looking. It is so proportioned that it is not until alongside that its size can really be appreciated.
Its giant stern tamp looks capable of gobbling up just about any conceivable cargo, including the diminutive MSM Don at the next berth. The pickup truck beside the ramp gives some idea of the scale.

Note: Despite my hopeful prediction it did not  load the cargo of windmill blades. They remain on the pier for another ship.
.

Note to Chronicle Herald Photo Editor

A file photo in today's Halifax Chronicle Herald purports to show a fishing boat maneuvering in sea smoke in Halifax Harbour. It is a wonderful shot by staff photographer Tim Krochak, and the boat is indeed steaming through wintery sea smoke, but it is not a fishing boat.
It is in fact the Halifax Port Authority's work boat Maintainer 1.

Built in 1995 by A.F Thériault in Meteghan, NS, Maintainer 1 is tasked with maintaining the fenders along the port's piers, picking up deadheads and other debris, and other general work around the port.
On July 14, 2002 it was struck by the ship Esperanza, and pinned against the pier. On February 16, 2003 it sank at its berth at pier 25 when a through hull fitting froze and burst. In both cases it was repaired, and in the latter the engine exhaust was re-routed through the cabin top.

Just for comparison puropses, here is a fishing boat:
The Oralee is based in Eastern Passage, and it often seen during lobster season working in along the shore at Point Pleasant Park, and usually operating singlehanded. It was built of fibre reinforced plastic in 1973 by R.D.Ross of Clark's Harbour, Cape Sable Island . In this photo it is using a steadying sail aft as its operator baits a trap. It is of the type called a Cape Islander, a common inshore fishing vessel of Atlantic Canada..
CCGS Sir William Alexander passes Ives Knoll outbound in the background.


.

Tuesday, November 12, 2013

Wellservicer

The British flag multi-purpose vessel Welllservicer put in to Halifax for a short visit today. Operated for Technip Canada Ltd, it has been working on the White Rose field off Newfoundland. It will now move to the Venture Field off Nova Scotia's Sable Island where it will carry out pipeline repair work. The work will include removal of an old spool, installation of a new spool, replacing protection mattresses and doing scour remediation. The work is expected to take until the end of the year.

The 111 meter long ship is fitted with a host of equipment to support diving and ROV activity. Among the most obvious pieces of kit is the double crane on a single pedestal. Working together the cranes can lift 130 tonnes. The ship is fitted with three thrusters forward, and three thrusters aft, which allow the ship to keep station within the very high tolerances of  DP 2 (Dynamic Positioning). Its six main engines develop 12,600 kW and produce a bollard pull of 110 tonnes.
Technip's website has full specs on this ship and the rest of the fleet: http://www.technip.com/en/our-business/fleet-facilities/vessels
With its large accommodation block and helicopter platform it is largely self-sustaining when at work, and remains at sea for periods of time up to two months without refueling.


.

Monday, November 11, 2013

More rail, on MSM Don

Another load of rail for CN arrived this morning on MSM Don. The Cyprus flag ship gave its last port as La Coruna, Spain,  and judging by its low profile, must have made the passage partially submerged.


Built in 2011 in Rongcheng, Chinja, this is a 4200 gross ton ship of 5400 deadweight tonnes (these numbers vary depending on the source, with gross tonnage also reported at 4156, and deadweight at 5646). It is typical of the new breed of small general cargo/bulkers of the coastal/ocean type. When built it was gearless, and had only the traveling gantry for hatch lifting. Sometime during this year it was fitted with two 30 tonne cranes. Two sister ships in the same fleet were built with 45 tonne cranes.


The ship is part of the Mastermind Shipmanagement Ltd fleet of Limassol, Cyprus, and is classed as a coastal ship in their fleet index. More info on the company and its ships may be found on their website:
http://www.mastermind-cyprus.com/

.

Painting at Halifax SHipyard, M.Charles and Holiday Island

New paint is in abundance at Halifax Shipyard as workers apply coatings to both Holiday Island and M.Charles.
1. Workers on lift trucks work on the blue anti-fouling bottom paint, while the black boot topping and whiter superstructure painting has been completed. Next comes the red banner painting. What is the black object at the centre of the loading ramp - it looks like the silhouette of a whale.

 
  2. Workers take a break on completion of the Coast Guard red hull paint on M.Charles.

.